document number: 83748 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.9, 20-oct-10 1 phototriac, zero crossing, 1.5 kv/s dv/dt, 600 v vo3062, vo3063 vishay semiconductors description the vo3062 and vo3063 triac driver family consists of a gaas infrared led optically coupled to a monolithic photosensitive zero crossing triac detector chip. the 600 v blocking voltage permits control of off-line voltages up to 240 vac, with a safety factor of more than two, and is sufficient for as much as 380 v. features ? 1500 v/s dv/dt minimum ? 600 v blocking voltage ? 100 ma on-state current ? zero crossing detector ? low input trigger current ? 6 pin dip package ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec applications ? household appliances ? triac drive/ac motor drives ? solenoid/valve controls ? office automation equipment/machine ? temperature (hvac)/lighting controls ? switching power supply agency approvals ? ul1577, file no. e52744 system code h ? cul - file no. e52744, equivalent to csa bulletin 5a ? din en 60747-5-5 (vde 0884) available with option 1 i179030_4 1 2 3 6 5 4 mt2 mt1 nc a c nc *zero crossing circuit zcc* v de 21842 ordering information vo306#-x0##t part number package option tape and reel agency certified/package trigger, current i ft (ma) ul, cul, bsi 5 10 dip-6 vo3063 vo3062 dip-6, 400 mil, option 6 vo3063-x006 vo3062-x006 smd-6, option 7 VO3063-X007T vo3062-x007t vde, ul, cul, bsi 5 10 dip-6, 400 mil, option 6 - vo3062-x016 smd-6, option 7 vo3063-x017t vo3062-x017t absolute maximum ratings (1) (t amb = 25 c, unless otherwise specified) parameter test condition part symbol value unit input reverse voltage v r 6v forward current - continuous i f 60 ma power di ssipation p diss 100 mw 10.16 mm > 0.7 mm 7.62 mm dip-6 option 7 option 6
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 83748 2 rev. 1.9, 20-oct-10 vo3062, vo3063 vishay semiconductors phototriac, zero crossi ng, 1.5 kv/s dv/dt, 600 v notes (1) stresses in excess of the absolute maximum ratings can cause pe rmanent damage to the device. functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. exposure to abs olute maximum ratings for e xtended periods of the time ca n adversely affect reliability. (2) refer to reflow profile for soldering conditions for surface mount ed devices (smd). refer to wave profile for soldering conditi ons for through hole devices (dip). note ? the thermal model is represented in the th ermal network below. each resistance value given in this model ca n be used to calcul ate the temperatures at each node for a given operating condition. the thermal resistance from board to ambient will be dependent on th e type of pcb, layout and thickness of copper traces. for a detailed explanation of the thermal model, please reference vishays thermal characteristics of optocouplers application note. output off state output terminal voltage vo3062, vo3063 v drm 600 v peak repetitive surge current pw = 100 s, 120 pps i tsm 1a power dissipation p diss 200 mw on-state rms current i t(rms) 100 ma coupler isolation test voltage t = 1 s v iso 5300 v rms total power dissipation p tot 300 mw operating temperature range t amb - 40 to + 100 c storage temperature range t stg - 55 to + 150 c soldering temperature (2) maximum 10 s t sld 260 c thermal characteristics parameter symbol value unit maximum led juncti on temperature t jmax. 125 c maximum output die j unction temperature t jmax. 125 c thermal resistance, junc tion emitter to board jeb 150 c/w thermal resistance, junc tion emitter to case jec 139 c/w thermal resistance, junction detector to board jdb 78 c/w thermal resistance, junction detector to case jdc 103 c/w thermal resistance, j unction emitter to junction detector jed 496 c/w thermal resistance, case to ambient ca 3563 c/w electrical characteristcs (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input reverse current v r = 6 v i r 10 a forward voltage i f = 30 ma v f 1.2 1.5 v output leakage with led off, either direction v drm = 600 v i drm 10 500 na critical rate of rise off-state voltage v d = 400 v dv/dt 1500 2000 v/s absolute maximum ratings (1) (t amb = 25 c, unless otherwise specified) parameter test condition part symbol value unit t a ca t c t jd t je t b ec eb dc db ba de t a 19996 package
document number: 83748 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.9, 20-oct-10 3 vo3062, vo3063 phototriac, zero crossi ng, 1.5 kv/s dv/dt, 600 v vishay semiconductors note ? typical values are characteristics of the device and are the re sult of engineering evaluations. typical values are for informa tion only and are not part of the te sting requirements. note ? as per iec60747-5-5, 7.4.3.8.1, this optoco upler is suitable for safe electrical insulation only within the sa fety ratings . compliance with the safety ratings shall be ensured by means of prodective circuits. coupler led trigger current, current required to latch output vo3063 i ft 5ma vo3062 i ft 10 ma peak on-sta te voltage, either direction i tm = 100 ma peak, i f = rated i ft v tm 1.7 3 v holding current, either direction i h 200 a inhibit voltage (mt1-mt2 voltage above which device will not trigger) v inh 12 22 v leakage in inhibited state i f = 10 ma maximum, at rated v drm , off state v drm2 250 1000 a safety and insulation ratings parameter test condition symbol min. typ. max. unit climatic classificati on iec68 part 1 40/85/21 pollution degree din vde 0109 2 comparative tracking index pe r din iec112/vde 0303 part 1, group iiia per din vde 6110 175 399 cti 175 highest allowable overvoltage transient overvoltage v iotm 8000 v peak maximum working insulation voltage recurring peak voltage v iorm 890 v peak insulation resistance at 25 c v io = 500 v r is 10 12 insulation resistance at t s v io = 500 v r is 10 9 insulation resistance at 100 c v io = 500 v r is 10 11 partial discharge test voltage method a, v pd = v iorm x 1.875 v pd 1325 v peak safety limiting values - maximum values allowed in the event of a failure safety power rating p so 400 mw safety current rating i si 150 ma safety temperature rating t si 165 c minimum external air gap (clearance) measured from input terminals to output terminals, shortest distance through air 7mm minimum external tracking (creepage) measured from input terminals to output terminals, shortest distance path along body 7mm electrical characteristcs (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit
www.vishay.com for technical questions, contact: optocoupleranswe rs@vishay.com document number: 83748 4 rev. 1.9, 20-oct-10 vo3062, vo3063 vishay semiconductors phototriac, zero crossi ng, 1.5 kv/s dv/dt, 600 v typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - forward voltage vs. forward current fig. 2 - off-state leakage current vs. temperature fig. 3 - on-state current vs. v tm fig. 4 - normalized trigger current vs. temperature fig. 5 - turn-on time vs. led current fig. 6 - normalized holding current vs. temperature 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1 10 100 i f - forward current (ma) v f - forward voltage (v) 19620 t a = 85 c t a = 25 c t a = - 40 c 1 10 100 1000 - 40 - 20 0 20 40 60 80 100 temperature (c) i lkg (na) 19619 - 100 - 80 - 60 - 40 - 20 0 20 40 60 80 100 - 2 - 1.5 - 1 - 0.5 0 0.5 1 1.5 2 on-state voltage v tm (v) on-state current i tm (ma) 19605 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 - 40 10 60 110 temperature (c) trigger current 19621 1 10 100 5 8 11 14 17 20 led current (ma) turn-on time (s) 19618 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 - 40 - 20 0 20 40 60 80 100 temperature (c) holding current 19608
document number: 83748 for technical questions, contact: optocoupleranswe rs@vishay.com www.vishay.com rev. 1.9, 20-oct-10 5 vo3062, vo3063 phototriac, zero crossi ng, 1.5 kv/s dv/dt, 600 v vishay semiconductors fig. 7 - turn-on time vs. temperature fig. 8 - trigger current vs. pulse width package dimensions in millimeters package marking 0 3 6 9 12 15 - 40 - 20 0 20 40 60 80 100 temperature (c) turn-on time (s) 19602 2.0 2.5 3.0 3.5 4.0 4.5 5.0 20 40 60 80 100 pulse width (s) i ft (ma) 19609 i178014_1 0.2 0.3 3.3 3.81 3.3 3.81 0.84 typ. 7.62 typ. 0.84 typ. 2.54 typ. 1 min. 0.46 0.51 1.22 1.32 6.3 6.5 8.5 8.7 pin one id 6 5 4 1 2 3 18 3 - 9 7.62 to 8.81 4 typ . iso method a 0.35 0.25 10.16 10.92 7.8 7.4 10.36 9.96 20 8 min. 7.62 typ. 4.6 4.1 8.4 min. 10.3 max. 0.7 option 7 option 6 21764-36 vo3062 v yww h 68
document number: 91000 www.vishay.com revision: 18-jul-08 1 disclaimer legal disclaimer notice vishay all product specifications and data are subject to change without notice. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, ?vishay?), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained herein or in any other disclosure relating to any product. vishay disclaims any and all li ability arising out of the use or application of any product describ ed herein or of any information provided herein to the maximum extent permit ted by law. the product specifications do not expand or otherwise modify vishay?s terms and conditions of purcha se, including but not limited to the warranty expressed therein, which apply to these products. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay. the products shown herein are not designed for use in medi cal, life-saving, or life-sustaining applications unless otherwise expressly indicated. customers using or selling vishay products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify vishay for any damages arising or resulting from such use or sale. please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such applications. product names and markings noted herein may be trademarks of their respective owners.
|
